| Category |
Albums |
Files |
|
3 |
271 |
|
| Other ShotsIf its not to do with beer or brewing put it here |
|
1 |
5 |
|
| User galleriesNot Used Anymore. You must now upload pictures to public galleries. |
|
7 |
0 |
|
| 276 files in 11 albums and 3 categories with 18 comments viewed 1254956 times |
| Random files |
Beer Stein8474 views"Hertog Jan Bieren" Boutique dutch brewery beer glass. Received as gift in Nederland in 2000.ANT.
|
|
The Barrel1822 viewsThis is a shot of the barrel I am using for my experimental barrel fermented and brett conditioned beer. I have installed a postmix keg valve to the barrel to take samples and to hook a beer tap up to it.bhami
|
|
Beer Day Out - Grist - Photo Taken By Phil3141 viewsAnother shot of the malt grist used for the brew at the Beer Day Out. It is not a bad grind with the husks largely intact and the centre of the grain crushed finely. The photo was taken by Phil who forwarded it onto me. Thanks Phil.bhami
|
|
Inside the portable keg fridge7623 viewsThis picture shows the rubber mat used as insulation on the inside of the portable keg fridge. The lid has also been insulated. The mat was purchased at Clarke Rubber for about $15, the plastic drum was sitting in the garage and the tap was a spare given to me by an old publican mate. Bags
|
|
|
|
Blue Sky Brewery - Brewery Tour3199 viewsThis file was e-mailed to me by Blue Sky Brewery to be included on their pint.com.au Breweries Directory listing. The listing can be found here http://www.pint.com.au/links/commercialbreweries/queensland/moreinfo/bluesky.htmbhami
|
|
4584 viewsI cut my existing Sankey boiler in half (gulp) then welded the bottom half to the salvaged keg, then finished the weld off inside grinding and polishing. I needed a torch in the bottom for this.Taz
|
|
Inside shot. C/O2 tank is on the outside now. 1797 viewsInside the Fridge. C/O2 tank is now on the outside. I placed it inside because I did not have place for it outside when the picture was taken.Beer-Guy
|
|
| Last additions |
HLT upgrade4601 viewsAutomated HLT filling. This was done using a simple two stage controller. The sensors are home made as I couldn't find anything off the shelf. These were made up of 1/2 inch BPT nipples welded top and bottom with plastic end caps used in rural irrigation to electrically isolate the probes from the keg which acts as ground. These caps were boiled in an electric jug for 15 minutes to test for heat and they stood up well. The probes used were stainless steel screws and nuts. Corrosion and electrolysis can be a real problem with this sort of gear.
TazOct 19, 2011
|
|
HLT upgrade2333 viewsTop water level sensor. Solenoid valve just seen on the riight.TazOct 19, 2011
|
|
HLT upgrade2335 viewsWater level sensorTazOct 19, 2011
|
|
Mindy5613 viewsFearless rat catcher protector of the grain supply and brew assistantTazAug 26, 2010
|
|
My brew assistant4542 viewsThe brew assistant doing what she does best between eating and hunting.TazAug 26, 2010
|
|
March Pump4640 viewsAn ungarded March Pump that needed a cover of some sort.TazAug 08, 2010
|
|
March Pump4662 viewsWasn't long before I realized the March Pump wasn't going to last long without some sort of protection against water and hot wort getting ito the cooling slots so I had this cover made upTazAug 08, 2010
|
|
4621 viewsTurning a 60 litre Sankey keg into a 85 litre one. The need to brew triple batches to fill 3 corny kegs I found the 60 litre keg was a tad to small which didn't allow for evaporation and head room for hot break, this is how I approached the problem. I cut the middle out of a damaged keg scavenged from an apple orchard.TazAug 08, 2010
|
|
